S2 Machine Guide
S2Machine Guide
Last updated
S2Machine Guide
Last updated
a-Y Right
b-Y Left
c-X Front
d-X Back
e- Motherboard box
f-X Top assemblies
g-Integrated module
h-Legs
*The corresponding parts will be represented by (Step1-4)in the installation procedure.
*Some components may not match the drawing, please take the actual product received
⑴ Assemble the frame(a)(b)(c)(d)with 4 screws as shown in the figure.
⑵ Pay attention to the direction of the scale on both sides
⑴ Slide the cantilever(f) into the frame along the long profile so that the long profile is sandwiched between the pulleys at both ends of the cantilever. As shown as (pic1)(pic2)
⑵ Use screws to secure the support feet and motherboard box (h)(e)as shown.
⑴ Insert belt along long profile guide(pic1)
⑵ Pass the belt through the two pulleys of the cantlilever and the timing pulley(pic2)
⑶ Push the X-axis against the X back plane, lock the belt(pic3),pass the belt through the square hole at the top of the other leg, pull the belt(pic4) with the other hand, and lock the belt(pic5) with screws and spacers.
⑷ Lock the other side of the belt in the same way.
1.Y-axis motor line 2.X limit switch cable 3.Y limit switch cable 4.X motor wire 5.Laser module cable
Note: the red port corresponds to the red plug and the white port corresponds to the white plug.
Connect the wires as shown in the picture.
Note: in order to clearly illustrate the position of the wiring. We have added numbers in the diagram, but in fact, there are no numbers on the terminal. To ensure the stability of the wiring terminal, secure the cable to the circle of the cable frame.” ”
⑴ Use flat round head screws M3x61,washer1, and cable tie1 as (pic1)
⑵ Use self-tapping round head screws M3x82, washer2,and cable ties2,as(pic2)
⑶ Use self-tapping round head screws M3x81, washers *1,and cable ties *1,as(pic3)
Note:the position where the screws need to be fixed is marked with a red circle, as shown in the figure.
Take out the laser module and insert the module into the sliding slot. When the red protective cover touches the surface of the focal length measurement block, tighten the side knob to fix it and complete the focusing.
Before using the laser engraver, please read this safety guide carefully, which mentions situations that require special attention and includes warnings about unsafe operations that may result in property damage or even endanger personal safety.
Our laser engravers use a class 4 laser. The laser is very powerful and may injure eyes and burn the skin.
We installed a shield on the laser module. The shield largely filters out the diffuse light from the laser spot. However, it is still recommended to wear laser goggles when using the laser engraver.
Do avoid exposing your skin to the class 4 laser beam, especially at close range.
Children under 14 years old are prohibited from using this product. Teenagers over 14 years old need adult supervision. When the laser module is on, do not touch it, otherwise you may burn your hands.
The high-intensity laser beam burns the substrate as it cuts, thus generating extremely high temperatures and heat. Some materials can catch fire and produce smoke during cutting.
When the laser beam hits the material, there is usually a small flame. It moves with the laser and does not stay lit after the laser passes by.
Do not leave the machine alone while the laser is working.
Be aware of flammable substances in the working environment. Always keep an fire extinguisher nearby.
There may be some smoke and irritating gas when the laser hits the material, and some of the gas will even be harmful to health, so please use it in a ventilated place.
Be sure to only use the laser engraver in horizontal position and make sure it is securely fixed to prevent a fire hazard if it is accidentally moved or dropped from the workbench during work.
It is forbidden to point the laser at people and animals.
We do not assume any responsibility for any improper use of this equipment or any damage or damage caused by improper use. The operator is obligated to use this laser engraving machine only in accordance with its designated purpose, instructions in its manual, and relevant requirements and regulations.
The laser engraver supports the most popular program LaserGRBL. LaserGRBL is an open-source, easy- touse program, but LaserGRBL only supports Windows System (Win XP / Win 7 / Win 8 /Win 10 / Win 11).
MacOS users can choose LightBurn, a professional laser program for windows and macOS. LightBurn has a one-month trial period, after which you need to pay to use it.
The laser engraver receives commands from the computer. It needs to stay connected to the computer, and do not shut the engraving program down (LaserGRBL or LightBurn),during the engraving process. since the calculations are done on the computer, the performance of the computer will affect the speed and even the quality of the engraving.
The following section will focus on the installation and use of LaserGRBL. For LightBurn, installation and configuration process will be briefly explained. Their official websites have program operation tutorials, which are very helpful for beginners.
Mac OS: LightBurn
Linux: LightBurn
Windows: LightBurn & LaserGRBL
LightBurn: https://lightburnsoftware.com/pages/download-trial
LaserGRBL ：https://lasergrbl.com/download/
software Forum: https:/forum.lightburnsoftware.com
Detailed tutorials on how to use the software can be found at www.woxcker.com
Please place the steel plate included in the package under the laser to protect your desktop.
Focus before engraving: Focusing is required before engraving, and the focus must be on the surface. Focal length of the engraved object.You can use a 2mm-Focal length measurement sheet to assist in the adjustment. When the red protective cover touches the surface of the focal length measurement block, tighten the side knob to fix it and complete the focusing..Improper focus setting will result in poor engraving or engraving failure.
The edge of the red laser protective cover must be parallel to the engraving object.
The cutting effect varies depending on the raw material.If you cannot successfully engrave or cut our recommended parameters with the following materials, try to increase the number of passes or reduce the speed.
If you feel that the laser energy is not strong enough, first check the laser lens to see if dust has contaminated the lens.Simply clean the lens to increase the laser power again.The laser lens and goggles cover should be cleaned regularly.
The tightness of the belt and pulley needs to be checked regularly.If the belt is loose: it can be re-installed and tightened; the pulley can be adjusted with the eccentric nut.
1.1.Before engraving or cutting, please adjust the focal length according to the instructions, and do not work at full power (100% power) for a long time;
1.2. After large-area engraving or long-term cutting, please clean the dust in the red protective cover;
1.3. After long-term work, the laser lens can be removed. It is recommended to use a roundheaded cotton swab to directly rotate and wipe the lens. The dust on the laser lens will be cleaned up, which will help restore the laser power. (The dust on the lens will block the laser and affect the laser power) It is recommended to clean the lens when you feel the laser is weakened. When wiping with a cotton swab, you can dip it in alcohol for better results;
1.4. The green light and blue light will flash on the top driver board of the laser module when it is working;
1.5. Please pay attention to whether the laser lens has cracks. If damaged, replace it in time. Before replacement, do not continue to use the module, otherwise the module will be scrapped.
1.6. After the module has been used for a period of time, the power decay begins to occur, which is a normal performance decay and a normal situation. The module itself is a consumable part, please replace it regularly as needed.
1.7. Please pay attention to the label on the side of the module;
2.1. Light up and click Start in the setting parameters, and the interface will appear with a super interface prompt. Please confirm that there is no super engraving interface and click "Yes". • "Yes" can be engraved/cut normally. If the interface is super, please adjust the working range and re-engraving.
2.2. If the motor beeps in the Y right/X back position, please do not panic. This noise is caused by engraving or cutting exceeding the maximum working size.This noise is caused by engraving or cutting exceeding the maximum working size. It will not cause any damage to the machine itself. It is recommended to adjust the engraving or cutting range.
4.1 The firmware can be obtained from the following locations
4.2 Do not connect the adapter , press the red switch as shown as [pic1-4.2]and hold on .
4.3 then insert the data cable from type C as [pic1-4.1]and wait for the computer to pop up the USB drive as [pic2](Please note that different computer settings may result in different icons).
4.4 Open the USB drive, drag the firmware to it, you can see the firmware refresh progress as [pic3], wait until the USB drive disappears, and the firmware refresh is complete.
4.5 If the operation fails, please follow steps 1-3 to try again. （Double click the red button engraving machine automatically go back to the origin).
